კარის პანელის საჭრელი დანადგარი

Door panel sizing machines bring a door leaf or a door component to its final length, width and edge profile, and on the larger models cut the lock, handle and lighting recesses in the same cycle. This page lists eight MIZRAK machines: the hand-set MZK Manuel Kapi Ebatlama, the NC RIPPER and NC Ripper KS for sizing and edge work, the NC RIPPER KK and NC Ripper Double PLC Control which add lock and handle machining, the three-axis MZK CNC Ripper Double, the PC-controlled Ripper CNC KKM machining unit, and the MZK RIPPER KKM. All are supplied by quotation.

განახლდა 2026-09-04

CNC კარის საფრეზი კარის კასრის CNC შემკრებიკარის პანელის საჭრელი დანადგარიკარის საკეტისა და ანჯამის ანოსაღები

ამ პარამეტრებით დანადგარი ვერ მოიძებნა

სცადეთ ფილტრის შემსუბუქება — ყველაზე ხშირად შემზღუდავია სიმძლავრე და დამუშავების სიგანე.

ფილტრის გასუფთავება

How to choose a door panel sizing machine

Choose by the operations you want finished on one machine. The eight MIZRAK machines here split three ways: sizing and edge milling, sizing plus lock and handle machining, and CNC hardware routing.

Sizing and edge milling only

Sizing-only machines suit shops that prepare hardware elsewhere. The MZK Manuel Kapi Ebatlama sizes by hand with a 45 to 90 degree tilting head, linear guideways and a digital display, cutting the lamp groove at once. The MZK NC RIPPER adds numerical control and the widest single-leaf envelope here, 1250 mm wide by 2700 mm long and 30 to 60 mm thick, and cuts rebated doors. The MZK NC Ripper KS works narrow components, 10 to 270 mm wide and 2500 mm long, on nine blades with a sanding unit and 5 mm architrave recessing.

Sizing plus lock and handle machining

Combining sizing and lock work removes the handling step where dimensional drift appears. The MZK NC RIPPER KK adds lock, handle and lighting-recess machining on a single bridge, sizing to 2200 x 1000 mm at 29.66 kW. The MZK NC Ripper Double PLC Control splits the work over two bridges and completes a full door plus the lock handle pocket in 1 minute 15 seconds at 30.41 kW.

CNC hardware routing

CNC earns its place where the hardware layout changes between door types. The MZK CNC Ripper Double adds three-axis servo routing of hinge, lock handle and faceplate seats after cutting leaves to 2200 x 1000 x 60 mm, at 38 kW. The Ripper CNC KKM is the machining unit without a sizing group: programmed X, Y and Z positions on 750 W servos, 1.5 kW and 2.2 kW spindles, 2000 mm blade machining capacity.

Power supply and installed load

Door sizing machines are three-phase installations. Published total power runs 25.75 kW on the KS, 29.66 kW on the KK, 30.41 kW on the NC RIPPER and NC Ripper Double PLC Control, and 38 kW at 80 A on the CNC Ripper Double, all at 380-400 V AC 50-60 Hz with air at 6 to 8 bar. Have an electrician confirm the board and cable run first.

Floor space and extraction

Every machine here claims a permanent bay. Bodies measure 3600 mm on the NC RIPPER, 4000 mm on the KS, 4500 mm on the KK, 5200 mm on the NC Ripper Double PLC Control and 5700 mm on the CNC Ripper Double, at 1450 to 2450 kg, with clear length at both ends for loading leaves. Extraction must be ducted before commissioning: the CNC Ripper Double takes two connections, 150 mm for the CNC group and 200 mm for the sizing group.

Tooling and what is quoted separately

Blade and cutter sets belong in the specification. The NC Ripper Double PLC Control uses fixed tooling sizes: 300 x 30 x 3.2 mm and 250 x 30 x 3.2 mm blades, a 125 x 20 x 3.2 mm milling cutter and dedicated lock, faceplate and handle cutters. Budget replacement tooling, extraction, a compressor if needed, and operator training.

Entry machines against the top of the range

The gap is automation and control, not cutting quality. The MZK Manuel Kapi Ebatlama is hand-set and simple to service, and Mizrak publishes no motor or footprint data for it; the MZK RIPPER KKM is likewise listed without a data sheet, so both are confirmed in writing. PLC machines hold a repeatable dimension through encoder-controlled axes; CNC models replace stops with programmed positions and cut non-standard hardware openings, but need a programmer rather than a setter.

როგორ ავირჩიოთ

Leaves wider than 1000 mm: The MZK NC RIPPER is the model that takes 1250 mm width and 2700 mm length; the twin-bridge and KK machines size to 2200 x 1000 mm.
Lock and handle pockets cut in-house: Specify the MZK NC RIPPER KK, the MZK NC Ripper Double PLC Control or the MZK CNC Ripper Double. The base NC RIPPER, the KS and the manual saw leave hardware work to a separate lock machine.
Frames, jambs and architraves rather than leaves: The MZK NC Ripper KS is the narrow-component machine, at 10 to 270 mm processing width and 2500 mm length, with a sanding unit and 5 mm architrave recess.
Hardware layout changes between door types: Choose a CNC machine. The MZK CNC Ripper Double routs hinge, lock handle and faceplate seats from programmed positions; the Ripper CNC KKM does the same as a machining unit for a shop that already sizes doors.
Cycle time matters more than flexibility: The MZK NC Ripper Double PLC Control sizes a leaf and opens the lock handle pocket in 1 minute 15 seconds on two bridges, under PLC control rather than CNC.
Installed electrical load available: Match the machine to the board: 25.75 kW on the KS, 29.66 kW on the KK, 30.41 kW on the NC RIPPER and NC Ripper Double PLC, 38 kW at 80 A on the CNC Ripper Double.
Floor length available in the bay: Allow 3600 mm for the NC RIPPER, 4000 mm for the KS, 4500 mm for the KK, 5200 mm for the NC Ripper Double PLC and 5700 mm for the CNC Ripper Double, plus loading space at each end.
Low volume or occasional door work: The MZK Manuel Kapi Ebatlama is the entry point, with a 45-90 degree tilting head, digital display and lamp groove cutting, and no PLC or lock group to programme.

ხშირად დასმული კითხვები

Which door panel sizing machine should I choose?

The right door panel sizing machine depends on how much of the door you want finished on one machine. If hardware is prepared elsewhere, the MZK NC RIPPER sizes and edge-mills leaves up to 1250 x 2700 mm and the MZK NC Ripper KS handles frame and architrave components 10 to 270 mm wide. If lock and handle pockets should be cut in the same cycle, the MZK NC RIPPER KK does that on a single bridge and the MZK NC Ripper Double PLC Control does it on two bridges in 1 minute 15 seconds. If hardware positions change between door types, the MZK CNC Ripper Double or the Ripper CNC KKM run those positions from a program.

What is the difference between the PLC and CNC RIPPER machines?

The difference between the PLC and CNC RIPPER machines is how positions are set. The MZK NC Ripper Double PLC Control uses PLC dimension entry on a touchscreen with encoder-controlled axes, which keeps operation close to a conventional sizing saw and holds the installed power at 30.41 kW. The MZK CNC Ripper Double replaces that with true three-axis servo contouring, raising installed power to 38 kW and machine length to 5700 mm, and it can produce shaped and non-standard hardware cut-outs. The PLC machine needs a setter; the CNC machine needs someone who can program it.

What electrical supply do MIZRAK door sizing machines need?

MIZRAK door sizing machines need a three-phase 380-400 V AC 50-60 Hz supply, plus compressed air at 6 to 8 bar. Published total power is 25.75 kW on the MZK NC Ripper KS, 29.66 kW on the MZK NC RIPPER KK, 30.41 kW on both the MZK NC RIPPER and the MZK NC Ripper Double PLC Control, and 38 kW at 80 A nominal current on the MZK CNC Ripper Double. Mizrak publishes no electrical data for the MZK Manuel Kapi Ebatlama or the MZK RIPPER KKM, so those ratings are confirmed in writing at quotation.

How much floor space and extraction does a door sizing line need?

A door sizing line needs a dedicated bay rather than a corner of the workshop. Machine bodies measure 3600 mm long on the MZK NC RIPPER, 4000 mm on the KS, 4500 mm on the KK, 5200 mm on the NC Ripper Double PLC Control and 5700 x 2100 x 2300 mm on the MZK CNC Ripper Double, which states a working area of 68 m2, and weights run from 1450 kg to 2450 kg. Extraction has to be ducted before commissioning; the MZK CNC Ripper Double alone takes two connections, 150 mm diameter for the CNC group and 200 mm for the sizing group. Add clear length at both ends of the machine for loading and unloading leaves.

Do these machines cut lock and hinge seats as well as sizing the door?

Only some of them cut lock and hinge seats. On this page the MZK NC RIPPER KK, the MZK NC Ripper Double PLC Control and the MZK CNC Ripper Double machine the lock and handle, and the CNC model adds hinge and faceplate seats under servo control. The MZK NC RIPPER, the MZK NC Ripper KS and the MZK Manuel Kapi Ebatlama size and mill only, so hardware preparation stays on a separate lock machine such as the MZK Kapi Kilit Plus. The Ripper CNC KKM is the reverse case: it machines hardware positions but does not size the leaf.

What drives the cost of a door panel sizing machine?

The cost of a door panel sizing machine is set by its configuration rather than by a catalogue figure. The main drivers are the number of bridges and whether a lock group is fitted, PLC versus CNC control, the sizing envelope, installed power from 25.75 kW to 38 kW, the blade and cutter package, the extraction and compressed air equipment the machine requires, and delivery, installation and operator training in Georgia. Send us your door sizes, your monthly volume and which hardware operations you want done in-house, and we will quote the matching configuration.