MIZRAK MZK 3200 Diamond S Sliding Table Panel Saw

The MZK 3200 Diamond S pairs a 3200 mm aluminium carriage, 435 mm wide, with motorised automatic 45-90 degree tilt and motorised vertical blade movement on an 820 kg machined frame. That is the Diamond S trade-off: powered setting, without the PLC and servo rear stop of the Diamond SX models.

Размер стола: 550 x 910 mm
Вес: 820 kg

Новый
Под заказ

Цена Цена по запросу

Price on the MZK 3200 Diamond S is driven by the 3200 mm carriage length specified rather than the heavier 3800 Diamond S, the decision to take motorised tilt and rise instead of the PLC and servo rear stop of the Diamond SX, the blade and scoring tooling package, extraction, and delivery and installation.

Запросить цену

WhatsApp +995 599 88 74 04

Ираклий Менеджер по продажам

Конфигурация под ваше напряжение и размеры
Доставка, монтаж и запуск на месте
Заводская гарантия и запчасти

The MZK 3200 Diamond S is the motorised-setting model of the 3200 mm class

The MZK 3200 Diamond S runs a 3200 mm long, 435 mm wide overhead-spindle aluminium carriage and sets blade angle and blade height by motor. Automatic 45-90 degree tilt and automatic up-and-down movement replace the handwheels used on the base Diamond, which matters most on mitred carcass parts and bevelled door edges where a half-degree error multiplies across a joint. The 4 kW main motor takes Ø250 x 30 mm to Ø300 x 30 mm blades at 4750-5250 rpm.

Scoring is part of the machine, not an accessory

A dedicated 0.75 kW motor drives the Ø125 x 20 mm scoring blade of the MZK 3200 Diamond S at 6800-7250 rpm. The scorer opens the coating on the underside of the board a fraction ahead of the main blade, which is the difference between a saleable melamine cabinet side and one that needs its edge hidden. Any workshop cutting faced board rather than solid timber should treat this as a requirement rather than an upgrade.

Who the MZK 3200 Diamond S is for

The MZK 3200 Diamond S fits furniture workshops and joineries that cut standard sheets daily, change blade angle several times a shift, and have floor space for a 3.2 m carriage but not for the 3.8 m machines. At 820 kg on a machined frame, the MZK 3200 Diamond S is a permanent installation rather than a machine that gets moved around the shop.

Where the MZK 3200 Diamond S sits in the range

Below the MZK 3200 Diamond S, the MZK 3200 Diamond keeps the same 4 kW motor and 435 mm carriage but uses a 9-spindle movement system with hand-set angle and height, and weighs 720 kg. Above it, the MZK 3200 Diamond SX adds a PLC control unit and a servo-driven linear cast-iron rear stop. The MZK 3200 Concord is a different tier again: 5.5 kW, 400 mm blade compatibility, pneumatic hold-down and a digital cast fence at 800 kg.

What is included with the MZK 3200 Diamond S

The specification covers the 550 x 910 mm main table, a 380 x 540 mm side extension sheet, a 785 x 970 mm rear extension sheet, a 1200 mm rip fence, the crosscut fence with ±45 degree setting and a 0-3000 mm stop range, and the scoring unit. Blades, extraction and electrical installation are separate.

Основные характеристики

3200 mm aluminium sliding carriage, 435 mm wide, on an overhead-spindle system
Motorised automatic 45-90 degree tilt and motorised vertical blade movement
4 kW main saw motor running Ø250 x 30 mm to Ø300 x 30 mm blades at 4750-5250 rpm
0.75 kW scoring motor with Ø125 x 20 mm blade at 6800-7250 rpm
820 kg machined frame with a 1400 mm machine height
Crosscut fence with ±45 degree setting and 0-3000 mm measuring stop range
550 x 910 mm main table plus 380 x 540 mm side and 785 x 970 mm rear extension sheets
Dust extraction port 845 mm above floor level, measured noise 80 dB

Технические характеристики

Диаметр пильного диска (внешний x внутренний, мин.-макс.): Ø250 x 30 mm – Ø300 x 30 mm
Частота вращения диска основной пилы: 4750 – 5250 rpm
Мощность двигателя основной пилы: 4 kW
Диаметр подрезного диска (внешний x внутренний): Ø125 x 20 mm
Частота вращения подрезной пилы: 6800 – 7250 rpm
Мощность двигателя подрезной пилы: 0.75 kW
Уровень шума: 80 dB
Размер основного стола: 550 x 910 mm
Размер бокового расширителя из листового металла: 380 x 540 mm
Размер заднего удлинителя из листового металла: 785 x 970 mm
Длина параллельного упора (на столе): 1200 mm
Ширина алюминиевой каретки: 435 mm
Длина алюминиевой каретки: 3200 mm
Угол наклона упора каретки: ±45° right and left
Диапазон регулировки упора каретки: 0 – 3000 mm
Регулировка наклона и высоты диска: Motorised automatic 45–90° tilt and motorised vertical movement
Система каретки: Overhead-spindle aluminium carriage, linear system
Станина: Machined frame
Высота патрубка аспирации от пола: 845 mm
Высота станка: 1400 mm
Вес станка: 820 kg

Преимущества

Motorised 45-90 degree tilt and blade rise remove the two most error-prone manual settings
3200 mm carriage handles a standard sheet lengthwise while fitting a smaller workshop than the 3800 models
820 kg machined frame gives noticeably more mass than the 720 kg base MZK 3200 Diamond

Важно учесть

Rip fence is still set by hand - no servo stop or digital position readout
Maximum cutting depth is not published in the supplier data for the Diamond S records
Extraction unit, blades and electrical installation are all additional to the machine price

Часто задаваемые вопросы

What supply does the MZK 3200 Diamond S require?

The MZK 3200 Diamond S has a 4 kW main saw motor and a 0.75 kW scoring motor, an installed motor load of 4.75 kW, plus the motors for automatic tilt and height. Mizrak does not publish the supply voltage or current for the MZK 3200 Diamond S, so the incoming supply, cabling and protection must be agreed with the dealer before delivery.

What size panels does the MZK 3200 Diamond S take?

The MZK 3200 Diamond S has a 3200 mm aluminium sliding carriage, which covers a standard 2800 mm or 3050 mm sheet cut lengthwise in a single pass. Crosscut capacity on the MZK 3200 Diamond S is set by the sliding table fence and its 0-3000 mm measuring stop range.

What tooling does the MZK 3200 Diamond S need?

The MZK 3200 Diamond S needs a main blade between Ø250 x 30 mm and Ø300 x 30 mm and a Ø125 x 20 mm scoring blade, neither of which is included in the published machine specification. For faced board, run a high tooth count main blade on the MZK 3200 Diamond S and keep the scorer set a fraction wider than the main kerf.

Does the MZK 3200 Diamond S need a separate extraction unit?

Yes. The MZK 3200 Diamond S has a dust extraction port 845 mm above the floor and no on-board extractor; the extraction unit, ducting and filters are separate purchases. The port diameter is not published for the MZK 3200 Diamond S, so confirm it before ordering ducting.

How much floor space and handling does the MZK 3200 Diamond S need?

The MZK 3200 Diamond S weighs 820 kg and stands 1400 mm high, so it needs a solid floor and a forklift or machine skates to install. Mizrak does not publish an overall footprint, but the 3200 mm carriage must be able to travel its full length in both directions, so plan on a clear run of roughly 6.5 m along the machine.

What does the MZK 3200 Diamond S not do?

The MZK 3200 Diamond S does not position the rip fence automatically - that is the MZK 3200 Diamond SX with its PLC and servo rear stop - and it has no pneumatic panel hold-down or digital cast fence, which belong to the MZK 3200 Concord. The MZK 3200 Diamond S is also a single-panel saw, not a beam saw for stacked cutting.

How much does the MZK 3200 Diamond S cost?

The MZK 3200 Diamond S is quoted rather than sold at a published price. The price of an MZK 3200 Diamond S depends on the 3200 mm carriage length chosen over the larger 3800 Diamond S, the decision to take motorised tilt and rise instead of the PLC and servo rear stop of the Diamond SX, the blade and scoring tooling package, extraction, and delivery and installation. Tell us your board sizes and angle work for a quotation.

What is the lead time for an MZK 3200 Diamond S?

The MZK 3200 Diamond S is built to order, so the lead time for an MZK 3200 Diamond S is confirmed at quotation against the current production schedule. Say at enquiry stage if the machine has to be commissioned by a set date.

Does an MZK 3200 Diamond S need professional commissioning?

An MZK 3200 Diamond S should be commissioned on site: levelling an 820 kg machine, squaring the 3200 mm carriage and fence, connecting a three-phase supply for the 4 kW saw, 0.75 kW scorer and the tilt and rise motors, verifying the motorised 45-90 degree angle against test cuts, and connecting extraction at the 845 mm port. Commissioning of the MZK 3200 Diamond S is quoted with the machine.

Which consumables should be budgeted beyond the MZK 3200 Diamond S machine price?

Beyond the MZK 3200 Diamond S machine price, budget main blades from Ø250 x 30 mm to Ø300 x 30 mm, Ø125 x 20 mm scoring blades and a dust extraction unit, none of which are listed in the supplier specification. Scoring blade sharpening is the consumable that most affects edge quality on an MZK 3200 Diamond S cutting melamine.

MZK 3200 DIAMOND S Цена по запросу Запросить цену