ხერხი-ფრეზის კომბინირებული ჩარხი
A saw and spindle moulder combination machine puts a sliding table saw and a full spindle moulder on one cast iron frame, so a joinery that cannot house two separate machines still gets both processes at full capacity. This category holds 2 HOLZMANN machines, the KF315VF2000 and the KF315VF2600, each combining a 315 mm sawblade with a two-piece 100 mm scoring blade and a 30 mm moulder spindle on an 860 x 890 mm table, with 1330 mm of rip capacity. The two models differ only in sliding table length, 2000 mm against 2600 mm. Both are supplied on quotation.
განახლდა
ამ პარამეტრებით დანადგარი ვერ მოიძებნა
სცადეთ ფილტრის შემსუბუქება — ყველაზე ხშირად შემზღუდავია სიმძლავრე და დამუშავების სიგანე.
Buy a saw and spindle moulder combination when floor space is the constraint
Floor space, not capability, is the argument for a combination machine. Both HOLZMANN KF315VF models put a 315 mm sliding table saw with a scoring unit and a 30 mm spindle moulder on one 860 x 890 mm cast iron table, changing duty with a turn instead of moving the workpiece to a second machine. The cost is setup time: a shop that saws and moulds alternately all day will move faster with two stand-alone machines. A joinery that cannot house both gets a full-capability saw and a full-capability moulder in a single 340 kg frame, which is why the combination is the honest answer for a small workshop.
Sliding table length is the only real choice between the two models
Carriage length decides which KF315VF to quote. The KF315VF2000 carries a 2000 x 270 mm sliding table trimming up to 2200 mm; the KF315VF2600 carries a 2600 x 270 mm table trimming up to 2700 mm, which is enough to cross-cut a full-length board or a 2.5 m door blank in one pass rather than two setups. Everything else is shared between the two machines: a 315 mm blade at 4500 rpm cutting 100 mm deep at 90 degrees and 80 mm at 45 degrees, a two-piece 100 mm scoring blade at 8500 rpm, 1330 mm of rip capacity at the parallel fence and a 750 x 590 mm outrigger table with support roller. Where panels rarely exceed 2200 mm, the shorter machine is the better use of floor.
The moulder half of a KF315VF is a full spindle moulder
The shaper unit on these machines is not a token attachment. Both KF315VF models give 100 mm of spindle stroke, 100 mm of clamping height, a 190 mm table opening and tool capacity to 180 mm below and 200 mm above the table, running four speeds from 1800 to 9000 rpm with LED speed indication. A shaper hood with roller guides, a protective plate, fine-adjustable aluminium fences and a 360 x 120 mm extractable mitre fence with workpiece end stop are part of the standard specification.
Power supply and extraction
Both models are offered in 230 V and 400 V versions, so a workshop without a three-phase connection is not shut out of this category. The KF315VF2000 is rated 3800 W (saw) and 2800 W (shaper) at S1 duty, the KF315VF2600 3000 W and 2800 W. Where three-phase supply exists it is the sensible specification for continuous work. Each machine extracts through two 100 mm ports, and the extractor must be sized for two ports and connected before commissioning, because a scoring saw cutting melamine produces fine dust a workshop vacuum will not hold.
Floor space and installation
Plan clear run-out, not just the footprint. A sliding carriage needs free floor at both ends of its travel, so the KF315VF2600 asks for roughly 600 mm more clear length along the slider than the KF315VF2000, on top of the outrigger side. Both machines work at 850 mm table height, weigh 340 kg and 337 kg net respectively, and need a level slab and a pallet truck to place them.
What to budget beyond the machine
Tooling is where a combination machine quietly becomes expensive. Saw blades, a replacement scoring blade, 30 mm bore moulder cutters, a power feed unit, extraction and the electrical connection are quoted separately. A spindle moulder is only as good as its cutter set, so scope the cutter package against the profiles the workshop actually produces.
როგორ ავირჩიოთ
- Sliding table 2000 mm vs 2600 mm
- Take the KF315VF2000 (2200 mm trim) for cabinet parts and shorter panels; take the KF315VF2600 (2700 mm trim) if full-length boards or 2.5 m door blanks are routine.
- Rip capacity 1330 mm
- Identical on both models and unusually generous for this class - a full sheet can be ripped at the parallel fence without an auxiliary table.
- Cutting height 100 mm at 90 degrees
- Both machines cut 100 mm at 90 degrees and 80 mm at 45 degrees with a 315 mm blade, which covers stacked panels, worktops and thick solid stock.
- Scoring unit fitted as standard
- Specify these machines rather than a plain table saw whenever melamine-faced board or veneered ply is cut; the 100 mm scorer at 8500 rpm prevents underside breakout.
- Spindle 30 mm, 100 mm stroke, 1800-9000 rpm
- Check your existing cutters are 30 mm bore. The four-speed range covers small rebate cutters at 9000 rpm and large heads at 1800 rpm.
- 230 V or 400 V version
- Order the 400 V version wherever three-phase is available; take 230 V only where the building has no three-phase supply and cannot be upgraded.
- Two 100 mm extraction ports
- Size the extractor for two simultaneous 100 mm connections and duct it before commissioning; extraction is not part of the machine.
- Clear run-out along the slider
- Allow free floor at both ends of the carriage travel plus space for the 750 x 590 mm outrigger, not just the 860 x 890 mm table footprint.