ძირითად შიგთავსზე გადასვლა
+995 599 88 74 04

HOLZMANN 10015509 Carbide Round Cutter Ø 16 mm, Ti-Coated

10015509 — HOLZMANN 10015509 Carbide Round Cutter Ø 16 mm, Ti-Coated 1 / 3

Ø 16 mm gives the HOLZMANN 10015509 the longest curved edge of any round tip in the range - 4 mm more diameter than the 10015506 and 0.05 kg of titanium-coated carbide against 0.02 kg. More edge in the cut is why the 10015509 is the roughing and hollowing choice on bowl blanks.

წონა
0.05 kg
  • ახალი
  • შეკვეთით
ფასი ფასი მოთხოვნით

The price of the 10015509 follows order quantity, the Ø 16 mm Ti-coated size against the smaller round tips, HOLZMANN's current list price and the exchange rate, freight consolidation, and the customs and tax treatment at landing.

ფასის მოთხოვნა
+995 599 88 74 04
ირაკლი გაყიდვების მენეჯერი
  • კონფიგურაცია თქვენს ძაბვასა და ზომებზე
  • მიწოდება, მონტაჟი და გაშვება ადგილზე
  • ქარხნული გარანტია და სათადარიგო ნაწილები

What the HOLZMANN 10015509 carbide round cutter is

The HOLZMANN 10015509 is a Ti-coated carbide round cutter of 16 mm diameter, the largest round tip in the HOLZMANN turning accessory range. The 10015509 is a replacement cutter for carbide-insert turning tools: the tip is screwed to the tool bar and exchanged when worn, so the turner never has to regrind an edge on a wheel.

Where a 16 mm round cutter is used

Diameter is what the 10015509 buys. A 16 mm curved edge takes a longer bite than the 12 mm or 6 mm HOLZMANN tips, which suits roughing bowl blanks, hollowing wide vessels and levelling long curved surfaces where a smaller cutter would need several more passes. Bowl and platter work in a production turning shop is the natural home of the 10015509, and the titanium coating is aimed at the abrasive, resinous timbers that shorten tool life fastest.

Choosing between the HOLZMANN round tips

Compared with the 12 mm 10015506, the 10015509 removes more material per pass but needs a heavier, better-supported tool and a firm stance at the rest; compared with the 6 mm 10015511 it will not enter small hollows or tight coves at all. Turners cutting flat shoulders and straight tapers should use the square tips 10015508 or 10015510 instead, and the 28 x 10 mm diamond tip 10015507 for points and V-grooves.

Delivery

The 10015509 arrives as a single carbide cutter of 0.05 kg net and 0.08 kg gross weight. No tool bar, handle or fixing screw is supplied. Carbide tips are not interchangeable across every brand of tool, so check the seat and screw of the existing turning tool before ordering.

ძირითადი მახასიათებლები

  • Ø 16 mm round carbide edge - the largest round radius in the HOLZMANN range, 4 mm above the 10015506
  • 0.05 kg net and 0.08 kg gross: more than twice the carbide mass of the Ø 12 mm and Ø 6 mm round tips
  • Titanium coated, aimed at the abrasive, resinous and green timber bowl blanks are usually cut from
  • A long sweeping arc removes more per pass when roughing and hollowing bowls and wide curves
  • The heavier cut wants a fully supported bar - Ø 16 mm loads a light tool harder than Ø 12 mm does
  • Shipped in the 58 x 138 x 10 mm carton, the larger of HOLZMANN's two tip pack sizes

ტექნიკური მახასიათებლები

Cutter shape
Round
Cutter diameter
Ø 16 mm
Coating
Ti-coated
Material
Carbide
Net weight
0.05 kg
Gross weight
0.08 kg
HOLZMANN article number
10015509

უპირატესობები

  • Largest round cutter in the HOLZMANN range at Ø 16 mm - fewer passes when roughing
  • Titanium coating slows wear in abrasive and resinous timber
  • Replaceable insert: no grinding wheel and no honing routine

გასათვალისწინებელი

  • Too large for tight coves, small hollows and box interiors
  • Heavier cutting load demands a well-supported tool bar and a stable lathe
  • Cutting tip only - no handle, tool bar or screw included, and fit is not universal

ხშირად დასმული კითხვები

Does the HOLZMANN 10015509 carbide cutter need 230 V or 400 V?
Neither. The HOLZMANN 10015509 is a carbide cutting tip with no motor and no electrical connection. Whether the wood lathe it is used on runs on 230 V single-phase or 400 V three-phase power makes no difference to the 10015509 itself; only the lathe is wired.
What does the HOLZMANN 10015509 not do?
The HOLZMANN 10015509 is a large round cutter and cannot work small detail. The Ø 16 mm 10015509 will not enter tight coves, narrow beads or small box interiors, cannot cut a flat shoulder or a sharp corner, and is supplied as the tip alone - no handle, tool bar or fixing screw.
Why choose the 16 mm round cutter over the 12 mm?
The HOLZMANN 10015509 takes a longer bite than the Ø 12 mm 10015506, so fewer passes are needed when roughing bowl blanks or levelling wide curves. In exchange the 10015509 loads the tool more heavily and needs a well-supported bar and a firm stance at the tool rest.
Is the HOLZMANN 10015509 suitable for a small hobby lathe?
The HOLZMANN 10015509 is the most aggressive round tip in the range, and on a light lathe with a small tool a Ø 16 mm cutter is harder to control. Smaller machines are usually better served by the Ø 12 mm 10015506 or the Ø 6 mm 10015511.
Will the HOLZMANN 10015509 fit any carbide turning tool?
Not necessarily. The HOLZMANN 10015509 seats in a specific pocket and is held by a specific screw, and these differ between tool brands and models. Verify the seat shape and screw size on the existing tool, or ask the dealer, before ordering the 10015509.
What determines the price of the HOLZMANN 10015509 round cutter?
The price of the HOLZMANN 10015509 Ø 16 mm Ti-coated round cutter is driven by quantity, by the size and coated grade (the Ø 12 mm 10015506 and Ø 6 mm 10015511 carry less carbide and price accordingly), by HOLZMANN's current list price and the exchange rate at order date, by whether the tips ride with a larger consignment, and by customs and tax treatment at landing. Give us the quantity and we will price the 10015509.
How long does it take to obtain a HOLZMANN 10015509?
The HOLZMANN 10015509 is ordered against its HOLZMANN article number and the current lead time is confirmed at quotation. No delivery window for the 10015509 is stated ahead of the order, because it depends on HOLZMANN's order book and on how the consignment is combined. Ask us for the current position when you request pricing.
Does the HOLZMANN 10015509 involve any installation cost?
No. The HOLZMANN 10015509 is a replacement carbide tip that screws into the round pocket of an existing turning tool, so there is no siting, levelling, electrical connection, extraction connection or commissioning to pay for. The only thing to confirm before ordering the 10015509 is that the tool's pocket accepts a Ø 16 mm insert.
What should be budgeted alongside the HOLZMANN 10015509 for bowl work?
With the HOLZMANN 10015509 budget for the round-pocket bar and handle it mounts in, spare retaining screws, and a finishing geometry to follow the roughing pass - typically the Ø 12 mm 10015506 or Ø 6 mm 10015511 for detail, and the square 10015508 for flats. If the work is heavy or out of balance, an eccentric clamping system such as the ES25070 or ES30110 belongs in the same budget.
10015509 ფასი მოთხოვნით ფასის მოთხოვნა