ძირითად შიგთავსზე გადასვლა
+995 599 88 74 04

NETMAK ST-1 Single-Wheel Automatic Power Feeder

ST-1 Otomatik Surucu Makinasi — NETMAK ST-1 Single-Wheel Automatic Power Feeder

One feed wheel instead of four is the whole point of the NETMAK ST-1: a single 110 x 50 mm wheel lets curved and shaped parts follow a template on a spindle moulder without a wheel train fighting the arc. The ST-1 keeps the 1-1.15 HP motor and 4-6 to 20-30 m/min feed ranges of the ST-4, at 60 kg rather than 80 kg.

ძრავის სიმძლავრე
0.86 kW
წონა
60 kg
გაბარიტები
460 x 1100 x 700 mm
  • ახალი
  • შეკვეთით
ფასი ფასი მოთხოვნით

Price on the ST-1 is driven by the mounting column and base plate specification for the host spindle moulder, the supply voltage the motor is built for, whether a template or ring fence package is quoted with the feeder, and whether the ST-1 is ordered on its own or with the moulder.

ფასის მოთხოვნა
+995 599 88 74 04
ირაკლი გაყიდვების მენეჯერი
  • კონფიგურაცია თქვენს ძაბვასა და ზომებზე
  • მიწოდება, მონტაჟი და გაშვება ადგილზე
  • ქარხნული გარანტია და სათადარიგო ნაწილები

What the ST-1 power feeder does

The ST-1 exists to solve one problem that multi-wheel feeders cannot: driving a curved workpiece safely past a cutter. Netmak specifies the ST-1 for feeding curved and bent components on a spindle moulder, and the single 110 x 50 mm wheel is the reason it works. Contact at one point only means the workpiece is free to pivot and follow a curved template or ring fence, while the driven wheel still supplies steady forward pressure and keeps the operator’s hands clear of the tooling.

Motor and feed speeds on the ST-1

Feed speed selection matters more on curved work than on straight runs, because a wheel that overdrives the part can push it away from the template. The ST-1 carries a 1-1.15 HP motor with a speed range of 1500-3000 rpm and four published feed ranges: 4-6, 8-12, 10-15 and 20-30 m/min. The slow end of that spread is where most curved and shaped moulding is done, particularly in hardwood, while the faster ranges cover light passes and softwood. The full 4-30 m/min spread means the ST-1 is not limited to curved work alone if a straight job needs a second feeder in the shop.

ST-1 compared with the four-wheel ST-4

Workpiece shape, not motor power, decides between the two feeders. The ST-1 and the ST-4 share the same 1-1.15 HP motor, the same 1500-3000 rpm speed range and the same four feed ranges, so neither is the more powerful machine. What separates them is wheel count: the ST-1 has one wheel and follows curves, while the ST-4 has four in-line wheels that hold a straight path and give better support on long straight stock. The ST-1 is also the smaller unit at 60 kg and 460 x 1100 x 700 mm, against 80 kg and 600 x 1100 x 700 mm for the ST-4. A workshop doing both kinds of work can leave an ST-4 on straight production and add an ST-1 for curved jobs rather than repeatedly refitting one feeder.

What Netmak publishes and what to confirm

Published data for the ST-1 covers wheel count and size, motor rating and speed, feed ranges, net weight and overall dimensions. It does not cover supply voltage or phase, or the mounting column and bracket arrangement. Confirm both points with Danadgarebi against the specific spindle moulder the ST-1 will be fitted to.

ძირითადი მახასიათებლები

  • Single 110 x 50 mm feed wheel that allows curved and shaped parts to follow a template
  • 1-1.15 HP drive motor, the same rating as the four-wheel ST-4
  • Motor speed range of 1500-3000 rpm
  • Four published feed ranges: 4-6, 8-12, 10-15 and 20-30 m/min
  • Net weight of 60 kg, 20 kg lighter than the four-wheel ST-4
  • Overall dimensions of 460 x 1100 x 700 mm, 140 mm narrower than the ST-4
  • Specified by Netmak for safe feeding of curved and bent parts on a spindle moulder

ტექნიკური მახასიათებლები

Product code
ST-1
Machine type
Automatic power feeder (Otomatik Surucu)
Number of wheels
1
Wheel size
110 x 50 mm
Motor power
1-1.15 HP
Motor speed
1500-3000 rpm
Feed rates
4-6 / 8-12 / 10-15 / 20-30 m/min
Net weight
60 kg
Overall dimensions
460 x 1100 x 700 mm
Intended application
Safe feeding of curved and bent workpieces on a spindle moulder

უპირატესობები

  • Single-wheel design is genuinely purpose-built for curved and shaped moulding work that four-wheel feeders cannot handle
  • Same 1-1.15 HP motor and same four feed ranges of 4-6 up to 20-30 m/min as the larger ST-4, so no power is sacrificed for the smaller format
  • At 60 kg and 460 x 1100 x 700 mm the ST-1 is the lighter and narrower feeder, easier to fit around a crowded moulder

გასათვალისწინებელი

  • Netmak does not publish supply voltage or phase for the ST-1, so the electrical specification must be confirmed separately before installation
  • One wheel gives noticeably less hold-down and fence pressure on long straight stock than a four-wheel feeder, so the ST-1 is a poor substitute for the ST-4 on straight production
  • Curved work still needs a template or ring fence, which is not part of the ST-1 and is not covered in the published specification

ხშირად დასმული კითხვები

What power supply does the ST-1 power feeder need?
Netmak does not publish a voltage or phase rating for the ST-1. The only electrical figures given for the ST-1 are motor output of 1-1.15 HP and a speed range of 1500-3000 rpm. Confirm voltage, phase and starter requirements with Danadgarebi before ordering rather than assuming the ST-1 matches an existing machine's supply.
Why does the ST-1 have only one wheel?
The ST-1 has one wheel specifically so that curved and shaped workpieces can be fed safely. A single 110 x 50 mm wheel touches the workpiece at one point, letting the part pivot around a curved template or ring fence, whereas three or four in-line wheels would define a straight path and fight the curve. That single-point contact is the defining design decision behind the ST-1.
Can the ST-1 be used for straight work as well?
The ST-1 can drive straight stock, but it gives less support than a multi-wheel feeder because only one wheel contacts the workpiece. For long straight runs of skirting, door stiles or ripped stock, the four-wheel ST-4 holds the workpiece more firmly along its full length; the ST-1 is the better choice where curved and shaped parts dominate.
What machine does the ST-1 mount on?
Netmak specifies the ST-1 for spindle moulders. The published specification does not describe the mounting column, base plate or bracket, so whether the ST-1 will bolt to a particular moulder table needs to be checked against that machine before purchase.
How much space and support does the ST-1 need?
The ST-1 weighs 60 kg net and measures 460 x 1100 x 700 mm overall. That 60 kg is carried by the host moulder's table through the feeder column, so the table and mounting must take the load of the ST-1 without flexing, and there must be swing clearance around the moulder for the feeder arm.
What does the ST-1 not do?
The ST-1 feeds the workpiece and does not cut it, so the ST-1 does not replace the cutter, the fence, the guarding or the dust extraction on the host machine. The ST-1 also does not include the curved template or ring fence that curved moulding work requires; those are made or bought separately.
How much does the NETMAK ST-1 cost?
The NETMAK ST-1 single-wheel power feeder is supplied by quotation, not at a published online price. The price of an ST-1 depends on the mounting column and base plate required for the specific spindle moulder it will be fitted to, the supply voltage the 1-1.15 HP motor is built for, whether a template or ring fence package is quoted alongside, and whether the ST-1 is ordered on its own or with the moulder. The ST-1 is normally quoted below the four-wheel ST-4, which is the heavier 80 kg feeder for straight production.
What is the lead time on a NETMAK ST-1?
The NETMAK ST-1 is built to order and the current lead time is confirmed at quotation. Where the ST-1 is bought with the spindle moulder it will be mounted on, the feeder is scheduled with that machine so the column can be fitted during one commissioning visit.
What is involved in fitting an ST-1 to a spindle moulder?
Fitting an ST-1 means bolting a mounting column to the spindle moulder, confirming the table can carry the feeder's 60 kg through that column, positioning the single wheel so the part is driven against the template or ring fence close to the cutter, and having a qualified electrician connect the supply. Netmak publishes no mounting details for the ST-1, so the column and base plate are matched to the host moulder at quotation.
What else has to be budgeted to run curved work on an ST-1?
The ST-1 drives the workpiece but does not guide it: curved and arched moulding also needs a template or jig for each profile and a ring fence or guide arrangement on the spindle moulder, none of which is part of an ST-1. Budget those alongside the feeder, plus a spare 110 x 50 mm feed wheel as the one routine consumable, since a single wheel wears faster per metre fed than the four wheels of an ST-4.
ST-1 Otomatik Surucu Makinasi ფასი მოთხოვნით ფასის მოთხოვნა