ძირითად შიგთავსზე გადასვლა

ფორმატ-საჭრელი ხერხი (ჰორიზონტალური)

A sliding table panel saw sizes sheet material by carrying the panel past the blade on an aluminium carriage, with a scoring blade ahead of the main blade to stop the faced underside chipping. This category covers 29 saws from HOLZMANN and MIZRAK, with carriage travel from 1320 mm on the HOLZMANN TS250FL to 3800 mm on the MZK 3800 PRESTIJ, Diamond, SPECIAL and Concord models, blades from 250 to 400 mm, and setting methods from fully manual to PLC control with a servo rear stop. All models are supplied by quotation.

განახლდა

CNC რუტერისაბალკე (ბიმ) ხერხისახვრეტი (საბურღი) დანადგარიფორმატ-საჭრელი ხერხი (ჰორიზონტალური)წიბოს დასაკრავი დანადგარი

ნაპოვნია 29 დანადგარი

ნაპოვნი დანადგარები

Carriage length is the first decision

Carriage travel decides what a sliding table saw can trim in one pass, so fix that figure before blade size or control level. Below 2000 mm – the HOLZMANN TS250FL at 1320 mm, TS250F at 1650 mm, TS250F1600 and TS315F1600 at 1600 mm, FKS305V16TOP at 1600 mm and the MIZRAK MZK 1500 PRESTIJ – the saw sizes doors, cabinet parts and pre-cut board in a shop that is already full. Between 2000 and 2800 mm, the TS315VF2000, TS315VF2600, MZK 2200 PRESTIJ, MZK 2800 PRESTIJ and MZK 2800 Diamond handle half sheets and long rips on a modest floor. At 3200 mm a standard sheet goes past the blade lengthwise in one uninterrupted pass, which is what the FKS305V32ECO, FKS305V32TOP, FKS400V32TOP, FKS400V32SMART, FKS400V32PRO, TS315VF3200 and the 3200 mm MIZRAK PRESTIJ, SPECIAL, Diamond, Diamond S, Diamond SX and Concord models are for. The 3800 mm MIZRAK saws take oversize sheets and door leaves, and the MZK 3800 PRESTIJ and MZK 3800 Concord add a profile support carriage for long narrow work.

Blade diameter, cutting height and the scoring unit

Blade diameter sets cutting height. The 250 to 254 mm HOLZMANN machines cut 80 mm at 90 degrees, the 315 mm machines cut 85 mm on the TS315F1600 and 100 mm on the TS315VF2600, every MIZRAK saw here cuts 80 mm at 90 degrees, and 400 mm blade capacity on the FKS400 family gives 130 mm of cutting height. A scoring unit – 0.75 kW on the MIZRAK saws and 750 W on the FKS305 models – cuts the lower face of a melamine or veneered panel a fraction ahead of the main blade, so any workshop sizing faced board should treat scoring as required rather than optional.

Manual, motorised or PLC setting

Setting method separates otherwise similar saws. The MIZRAK PRESTIJ line is hand-set throughout; the SPECIAL and Diamond S add motorised 45-90 degree tilt and motorised blade rise; the Diamond SX adds PLC control with a servo linear cast-iron rear stop; and the Concord pairs a 5.5 kW main saw with automatic tilt, pneumatic panel hold-down and a digital cast-iron fence. On the HOLZMANN side the FKS400V32TOP sets tilt by hand while raising blade and scorer electrically, the FKS400V32SMART positions rip fence, height and 0-45 degree tilt from a display, and the FKS400V32PRO adds motorised rip-fence positioning keyed in as a number.

Power supply, floor space, extraction and blades

Most sliding table saws here are 400 V three-phase machines, including the FKS305V32ECO and the FKS400 family. Two models answer a shop with no three-phase connection: the TS315F1600 is offered in a 230 V single-phase and a 400 V three-phase version, and the TS315VF2600 is the one scoring sliding table saw on this page that can be ordered as 230 V single-phase. Floor space is roughly twice the carriage length along the line of cut plus the width of the outrigger table, so a 3200 mm saw wants a clear run of about six and a half metres. Extraction connects at the blade hood and the lower cabinet. Blades are usually a separate line on the quotation: the FKS400V32TOP is the one FKS supplied with a main blade and scorer, and the TS250F arrives with a 254 x 30 x 3.0 mm 36-tooth blade, edging shoe and push stick. Carriage length, control level, blade set, extraction, delivery and installation are the figures that move the final price.

როგორ ავირჩიოთ

Carriage travel 1320-1650 mm
Sizing doors, cabinet parts and pre-cut board inside a small shop: TS250FL, TS250F, TS250F1600, TS315F1600, FKS305V16TOP and the MZK 1500 PRESTIJ.
Carriage travel 2000-2800 mm
Half sheets, long rips and solid timber with a shorter floor run: TS315VF2000, TS315VF2600, MZK 2200 PRESTIJ, MZK 2800 PRESTIJ and MZK 2800 Diamond.
Carriage travel 3200 mm
A standard full sheet trimmed lengthwise in one pass - the normal choice for cabinet production, from the FKS305V32ECO and TS315VF3200 to the MZK 3200 PRESTIJ, SPECIAL, Diamond, Diamond S, Diamond SX and Concord.
Carriage travel 3800 mm
Oversize sheets and door leaves: MZK 3800 PRESTIJ, MZK 3800 SPECIAL, MZK 3800 Diamond, Diamond S, Diamond SX and Concord; the PRESTIJ and Concord add a profile support carriage.
Blade diameter and cutting height
250-254 mm blades cut 80 mm at 90 degrees; 315 mm blades cut 85-100 mm; the FKS400 family accepts 400 mm blades for 130 mm cutting height on thick stacks and solid timber.
Scoring unit
Treat scoring as required for melamine and veneered board: 0.75 kW on the MIZRAK saws, 750 W on the FKS305 models, and a 100 mm scorer at 8500 min-1 on the TS315VF3200.
Setting method
Hand-set on the PRESTIJ and Diamond lines; motorised tilt and rise on the SPECIAL, Diamond S and FKS400V32SMART; PLC and servo rear stop on the Diamond SX; motorised rip fence on the FKS400V32PRO.
Supply voltage
Plan for 400 V three-phase on most models; the TS315F1600 is offered in 230 V single-phase and 400 V versions and the TS315VF2600 is the only scoring model here available on 230 V.

ხშირად დასმული კითხვები

What carriage length should a sliding table panel saw have?
Choose the carriage length of a sliding table panel saw from the largest panel you cut in one pass. Under 2000 mm - the HOLZMANN TS250FL, TS250F, TS250F1600, TS315F1600, FKS305V16TOP and the MIZRAK MZK 1500 PRESTIJ - suits doors, cabinet parts and pre-cut board in a crowded shop. 2000-2800 mm handles half sheets and long rips. 3200 mm takes a standard full sheet lengthwise in one uninterrupted pass and is the usual cabinet-shop choice, while 3800 mm models handle oversize sheets and door leaves.
Is there a panel saw that works on single-phase 230 V?
Yes. Most sliding table panel saws on this page are 400 V three-phase machines, but the HOLZMANN TS315F1600 is offered in a 230 V single-phase version as well as a 400 V three-phase version, and the TS315VF2600 is the one scoring sliding table saw here that can be ordered as 230 V single-phase, with a 100 mm cut at 90 degrees and a 2600 mm carriage. If the workshop has no three-phase connection, those two models are the starting point; otherwise, budget the electrical installation with the machine.
How much floor space and extraction does a panel saw need?
A sliding table panel saw needs roughly twice its carriage length along the line of cut, because the carriage travels fully forward and fully back, plus the width of the outrigger table and room for the operator to walk the panel round. A 3200 mm saw therefore wants a clear run of about six and a half metres, and a 3800 mm machine more. Extraction connects at the blade hood and the lower cabinet; a scoring saw cutting faced board produces fine dust that a shop extractor or cyclone unit should handle continuously.
Do I need the scoring unit on a panel saw?
A scoring unit is effectively required on a panel saw if the shop cuts melamine, laminated or veneered board, because the scorer cuts the lower face a fraction ahead of the main blade and prevents the underside chipping out. On this page scoring is 0.75 kW on the MIZRAK saws and 750 W on the FKS305 models, with a 100 mm scorer at 8500 min-1 on the TS315VF3200. For solid timber and unfaced material the scorer matters less, but almost every furniture workshop will use it daily.
What makes one panel saw more expensive than another?
On a sliding table panel saw the price is driven by carriage length, frame weight, main saw power, and above all the setting method. The MIZRAK PRESTIJ saws are hand-set; the SPECIAL and Diamond S add motorised tilt and blade rise; the Diamond SX adds PLC control with a servo cast-iron rear stop; the Concord adds a 5.5 kW drive, pneumatic hold-down and a digital fence. On the HOLZMANN side the FKS400V32PRO adds motorised rip-fence positioning over the FKS400V32SMART and FKS400V32TOP. Blades, extraction, delivery and installation are quoted alongside, so every model here is priced by configuration.
What is the difference between the MIZRAK PRESTIJ, SPECIAL, Diamond, Diamond S, SX and Concord saws?
The MIZRAK panel saw families differ mainly by how the machine is set, not by cutting capacity - PRESTIJ, SPECIAL, Diamond and Diamond S all cut 80 mm at 90 degrees with a 4 kW saw motor and 0.75 kW scorer. PRESTIJ is fully hand-set; SPECIAL and Diamond S add motorised 45-90 degree tilt and motorised blade rise; Diamond SX adds PLC control and a servo linear cast-iron rear stop; Concord moves to a 5.5 kW main saw with automatic tilt, pneumatic panel hold-down and a digital cast-iron fence. Choose the level of automation your batch sizes justify, then choose 3200 or 3800 mm of travel.